This page describes the configuration file for the Hercules S/370, ESA/390, and z/Architecture emulator.
The configuration file hercules.cnf contains the processor and device layout. It is roughly equivalent to the IOCDS on a real System/390. The configuration file is an ASCII text file.
Please note that the below example configuration file should
not be considered a good example of how an actual configuration
file should look! It is only meant to illustrate what some of the supported
configuration file statements look like and how they are used.
|
Blank lines, and lines beginning with a # sign or an asterisk, are treated as comments.
Except for the ARCHLVL statements, system parameter statements may appear in any order but must precede any device statements. Each system parameter must be on a separate line. The following system parameters may be specified:
ARCHLVL S/370 | ESA/390 | ESAME | z/Arch
Specifies the initial architecture mode:
S/370 for OS/360, VM/370, and MVS 3.8.
ESA/390 for MVS/XA, MVS/ESA, OS/390, VM/ESA, VSE/ESA,
Linux/390, and ZZSA.
z/Arch or ESAME for z/OS and zLinux. This is the default.
ESAME is similar to z/Arch.
When z/Arch or ESAME is specified,
the machine will always IPL in ESA/390 mode,
but is capable of being switched into z/Architecture mode after IPL.
This is handled automatically by all z/Architecture operating systems.
The ESAME mode is equivalent to z/Architecture mode at Architecture Level 2.
The z/Arch mode is equivalent to z/Architecture mode at Architecture Level 3.
The synonyms ALS0, ALS1, ALS2 and ALS3 may be used to specify S/370, ESA/390, ESAME or Z/Arch respectively.
Note: This statement used to be called ARCHMODE in previous versions of Hercules
but the use of ARCHMODE has been deprecated in favor of the new ARCHLVL
statement. Existing ARCHMODE statements should be changed to ARCHLVL
instead.
For the time being however, ARCHMODE is still accepted and is treated as
simply a synonym for the ARCHLVL statement.
ARCHLVL ENABLE | DISABLE | QUERY facility [archmode]
Specifies a particular STFLE facility to be enabled or disabled, or a query of the current settings.
Use QUERY ALL to obtain a list of valid facility names
that may be used for the given archmode.
Alternatively, you can also specify the actual STFLE bit number to be turned off or on
(disabled or enabled) using the format BITnn where 'nn'
corresponds to the exact STFLE facility bit you wish to be forced on or off. A popular
one among the VM crowd is ENABLE BIT44 to force the PFPO Facility bit on.
The optional archmode argument limits the enable,
disable or query function to a specific architecture.
It should be noted that attempts to enable or disable a facility that a given
architecture does not support are ignored without error. The default value is
whatever architecture mode was previously established by a preceding
ARCHLVL statement or the default mode if there was no
preceding ARCHLVL statement.
ASN_AND_LX_REUSE DISABLE | ENABLE (deprecated)
Specifies that the ASN-and-LX-Reuse Facility (ALRF) is to be disabled
or enabled. The default is disabled. This is a z/Architecture-only
feature (it is always disabled for S/390 or ESA/390). Set this
to ENABLE if the operating system supports
this z/Architecture feature and the use of this feature is desired.
Set it to DISABLE or do not specify anything
if the operating system doesn't support this feature, and it
inadvertently sets CR0 bit 44 to 1, usually leading to unexpected
program interrupt when instructions such as LASP are issued.
ASN_AND_LX_REUSE may be abbreviated as ALRF.
Note: The ASN_AND_LX_REUSE statement has been superseded
by "ARCHLVL ENABLE/DISABLE ASN_LX_REUSE" and is thus deprecated.
Existing ALRF or ASN_AND_LX_REUSE statements
should be changed to use the new ARCHLVL
facility statement format instead.
AUTOMOUNT [±]directory
Specifies the host system directory where the guest is allowed or not allowed to automatically load virtual tape volumes from. Prefix allowable directories with a '+' plus sign and unallowable directories with a '-' minus sign. The default prefix if neither is specified is the '+' plus sign (i.e. an allowable directory).
Caution: Enabling this feature may have security consequences depending on which allowable host system directories you specify as well as how your guest operating system enforces authorized use of the Set Diagnose (X'4B') channel command code.
All host system virtual tape volumes to be "automounted" by the guest must reside within one of the specified allowable host system directories or any of its subdirectories while not also being within any of the specified unallowable directories or any of their subdirectories, in order for the guest-invoked automount to be accepted.
Note: specifying a disallowed automount directory does not preclude the
Hercules operator from manually mounting any desired file via the
devinit panel command -- even one in a currently defined
"disallowed" automount directory. The AUTOMOUNT statement only controls
guest-invoked automatic tape mounts and not manual tape mounts performed
by the Hercules operator.
All directories must be specified on separate statements, but as many
statements as needed may be specified in order to describe the desired
allowable/unallowable directories layout. For convenience, an
automount panel command is also provided to dynamically
add/remove new/existing allowable/unallowable automount
directories at any time.
The automount feature is activated whenever you specify at least one allowable or unallowable directory. If only unallowable directories are specified, then the current directory becomes the only defined allowable automount directory by default.
All specified directories are always resolved to fully-qualified absolute directory paths before being saved.
Refer to the description of the virtual tape device 'noautomount' option for more information.
CCKD cckd-parameters
The CCKD command and initialization statement can be used to affect cckd processing. The CCKD initialization statement is specified as a Hercules configuration file statement and supports the same options as the cckd panel command. Refer to the Compressed Dasd Emulation web page for more information.
CMPSCPAD alignment
The CMPSCPAD command and initialization statement is used to define the zero padding storage alignment boundary for the CMPSC-Enhancement Facility. It must be a power of 2 value ranging anywhere from 1 to 12.
CODEPAGE mapping
Specifies the codepage conversion mapping table used for ASCII/EBCDIC translation.
default specifies traditional Hercules codepage mapping.
Other supported predefined codepage mappings are:
Mapping Description Transparent? ASCII EBCDIC 437/037437 PC United States 037 United States/Canada no 437/500437 PC United States 500 International no 437/1047437 PC United States 1047 Open Systems Latin 1 no 819/037819 ISO-8859-1 037 United States/Canada YES 819/037v2819 ISO-8859-1 037 United States/Canada version 2 YES 819/273819 ISO-8859-1 273 Austria/Germany YES 819/277819 ISO-8859-1 277 Denmark/Norway YES 819/278819 ISO-8859-1 278 Finland/Sweden YES 819/280819 ISO-8859-1 280 Italy YES 819/284819 ISO-8859-1 284 Spain YES 819/285819 ISO-8859-1 285 United Kingdom YES 819/297819 ISO-8859-1 297 France YES 819/500819 ISO-8859-1 500 International YES 819/1047819 ISO-8859-1 1047 Open Systems Latin 1 YES 850/273850 PC Latin 1 273 Austria/Germany YES 850/1047850 PC Latin 1 1047 Open Systems Latin 1 no 1252/0371252 Windows Latin 1 037 United States/Canada no 1252/037v21252 Windows Latin 1 037 United States/Canada version 2 no 1252/10471252 Windows Latin 1 1047 Open Systems Latin 1 no 1252/11401252 Windows Latin 1 1140 United States/Canada with Euro YES ISOANSI/037ISO ANSI 037 United States/Canada YES
The transparency column indicates whether translating from ASCII to EBCDIC (or vice versa) and back again yields results identical to the original text.
If no codepage is specified then the environment variable HERCULES_CP
will be inspected. If the environment variable is not found then
the traditional non-transparent default codepage mapping
is used.
Other codepages can be defined by means of the cp_updt
panel command (which is supported as a configuration file statement
as well). Enter the panel command help cp_updt for more
information.
CNSLPORT nnnn -or- host:port
Specifies (typically) the port number (in decimal) to which tn3270 and telnet clients should connect. If an invalid value is specified Hercules defaults to port 3270.
The CNSLPORT statement may also be specified as
host:port, where host identifies the
IP address of the host interface the telnet console server should
bind to (listen for connections on). If not specified the server
will accept connections from any host interface.
See the Telnet/tn3270 Console How-To for additional information about setting up a telnet or tn3270 client.
CONKPALV (idle,intv,count)
Specifies the tn3270 console and telnet clients keepalive option values that control automatic detection of disconnected tn3270/telnet client sessions.
idle specifies the number of seconds
of inactivity until the first keepalive probe is
sent (idle time until first probe, or probe frequency).
intv
specifies the interval in seconds between when successive
keepalive packets are sent if no acknowledgement is received from
the previous one (i.e. the timeout value of the probes themselves).
count specifies the number of unacknowledged
keepalive packets sent before the connection is considered to have
failed.
The default values for Windows are 3, 1, and 10. For non-Windows systems it is 3, 1, and 9. That is, send the initial probe 3 seconds after the connection goes idle and then wait no more than one second for it to be responded to. If it is not responded to within one second, then send up to 9 more probes (for a total of 10), each of which must also timeout without being responded to before the client is considered as having died and the connection thus automatically closed.
Note: This is a built-in feature of TCP/IP and allows detection of unresponsive TCP/IP connections and not idle clients. That is to say, your connection will not be terminated after 3 seconds of idle time. Your 3270 session can remain idle for many minutes or hours or days without any data being transmitted. If the TCP/IP stack at the other end of the connection -- not your 3270 client itself -- fails to respond to the internal keepalive probe packets however, then it means that the TCP/IP stack itself is down or there has been a physical break in the connection.
Thus, even if your 3270 client is completely idle, your system's TCP/IP stack itself should still respond to the keepalive probes sent by the TCP/IP stack at the Hercules end of the link. If it doesn't, then TCP/IP will terminate the tn3270/telnet session which will cause Hercules to disconnect the terminal.
The three values can also be modified on-demand via the conkpalv
panel command, which has the exact same syntax. Note that the syntax is
very unforgiving: no spaces are allowed anywhere within the parentheses
and each value must be separated from the other with a single comma.
Please also note that not all systems support being able to modify
all three values. That is, not all values may be modifiable. It is operating
system dependent which values you can change and which values you cannot.
On Windows for example, the count value is ignored
and cannot be changed from its default value of 10. Other systems may
ignore one or more or all three values and use platform defaults instead.
This is entirely system dependent. Check your system's documentation for details
regarding which values can be changed and which cannot as well as how to
adjust your system's default values.
CPUIDFMT 0 | 1
Specifies the format of the CPU ID the STIDP instruction should store. Refer to the LPARNUM statement for more information.
CPUMODEL xxxx
Specifies the 4 hexadecimal digit CPU machine type number (known prior to ESA/390 as the model number) stored by the STIDP instruction.
Note: Hercules makes no attempt to emulate all aspects of, or features of, a given CPU model. The CPUMODEL statement defines a purely cosmetic value only. It defines only the value that the STIDP (Store CPU ID) instruction stores, and nothing more.
CPUPRIO nn
Specifies the priority of the CPU thread. Default is a nice value of 15, which means a low priority such that I/O can be scheduled and completed in favour of CPU cycles being burned. On Multi-CPU systems, a real CPU can be "dedicated" to Hercules, by giving the CPU thread a very high dispatching priority (-20). See "Thread Priorities" below for more information.
Caution: CPUPRIO should not have a higher dispatching priority than the TOD Clock and timer thread.
CPUSERIAL xxxxxx
Specifies the 6 hexadecimal digit CPU serial number stored by the STIDP instruction. In BASIC mode, the high-order digit may be replaced with the processor number when MAXCPU > 1; in LPAR mode, the two high-order digits are replaced with either the LPAR number or the CPU number and LPAR number with the full serial number available via the STSI instruction. The default serial number is 000001.
CPUVERID xx
Specifies the 2 hexadecimal digit CPU version code stored by the STIDP instruction. The default version code is FD when ARCHLVL S/370 or ARCHLVL ESA/390 is specified. For the z/Architecture mode, the version code is always stored as 00 and the value specified here is ignored.
DEFSYM symbol value
Defines symbol symbol as to contain value value. The symbol can then be the object of a substitution later in the configuration file or for panel commands. If value contains blanks or spaces, then it should be enclosed in double quotation marks ("). See substitutions for a more in-depth discussion on this feature.
Substitution is available even in configuration statements,
meaning it is possible to perform substitution in the DEFSYM statement itself.
However, symbols are always defined as the last step in the process, so attempting
to self define a symbol will result in an empty string:
DEFSYM FOO $(FOO)
DEVPRIO nn
Specifies the priority of the device threads. The default value is 8. See "Thread Priorities" below for more information.
Caution: DEVPRIO should not have a higher dispatching priority than the TOD Clock and timer thread.
DEVTMAX -1 | 0 | nnn
Specifies the maximum number of device threads allowed.
Specify -1 to cause 'one time only' temporary threads to be
created to service each I/O request to a device. Once the I/O request is
complete, the thread exits. Subsequent I/O to the same device will cause
another worker thread to be created again.
Specify 0 to cause an unlimited number of 'semi-permanent'
threads to be created on an 'as-needed' basis. With this option, a thread
is created to service an I/O request for a device if one doesn't already
exist, but once the I/O is complete, the thread enters an idle state waiting
for new work. If a new I/O request for the device arrives before the timeout
period expires, the existing thread will be reused. The timeout value is
currently hard coded at 5 minutes. Note that this option can cause one thread
(or possibly more) to be created for each device defined in your
configuration. Specifying 0 means there is no limit to the
number of threads that can be created.
Specify a value from 1 to nnn to set an upper limit
to the number of threads that can be created to service any I/O request to
any device. Like the 0 option, each thread, once done servicing
an I/O request, enters an idle state. If a new request arrives before the
timeout period expires, the thread is reused. If all threads are busy when
a new I/O request arrives however, a new thread is created only if the
specified maximum has not yet been reached. If the specified maximum number
of threads has already been reached, then the I/O request is placed in a queue
and will be serviced by the first available thread (i.e. by whichever thread
becomes idle first). This option was created to address a threading issue
(possibly related to the cygwin Pthreads implementation) on Windows systems.
The default for Windows is 8. The default for all other systems
is 0.
DIAG8CMD DISABLE | ENABLE [ECHO | NOECHO]
When ENABLE is specified, commands issued through the Diagnose 8 interface
will be executed by Hercules as Hercules commands. When set to DISABLE,
commands issued through the Diagnose 8 interface will generate a Specification
Exception program interrupt on the issuing CPU.
An optional second argument can be given to request whether the commands
issued using the Diagnose 8 interface will be traced at the console. This may be
useful for programs that routinely issue panel commands using the Diagnose 8 interface.
When ECHO is specified, a message is issued as the panel is about to issue
the command, the command is redisplayed as if it was entered through the panel input
line, and a final message is issued to indicate the command completed. When NOECHO
is specified, no such messages are displayed and the command completes silently.
The value of ECHO or NOECHO has no effect on
command output being placed into a response buffer if the Diagnose 8 interface
requested one.
The default is DISABLE NOECHO
Caution: Enabling this feature may have security consequences.
When this feature is enabled it is possible for guest operating systems
running under Hercules to issue commands directly to the host operating system
by means of the Hercules sh (shell) command. This ability may be
disabled via the SHCMDOPT statement.
ECPSVM YES | NO | LEVEL nn
Specifies whether ECPS:VM (Extended Control Program Support : Virtual Machine)
support is to be enabled. If YES is specified, then the support
level reported to the operating system is 20. The purpose of
ECPS:VM is to provide to the VM/370 Operating system a set of shortcut
facilities to perform hypervisor functions (CP Assists) and virtual
machine simulation (VM Assists). Although this feature does not affect
VM Operating system products operating in XA, ESA or z/Architecture mode,
it will affect VM/370 and VM/SP products running under VM/XA, VM/ESA or z/VM.
Running VM/370 and VM/SP products under VM/XA, VM/ESA or z/VM should be
done with ECPS:VM disabled. ECPS:VM should not be enabled in an AP or MP
environment. ECPS:VM has no effect on non-VM operating systems. It is
however recommended to disable ECPS:VM when running native non-VM operating
systems. If a specific LEVEL is specified, this value will be reported
to the operating system when it issues a Store ECPS:VM level, but it
doesn't otherwise alter the ECPS:VM facility operations. This is a partial
implementation.
ENGINES [nn*]CP|IL|AP|IP[,...]
Specifies the type of engine for each installed processor. The default engine type is CP.
nn* is an optional repeat count. Spaces are not permitted.
Examples:
ENGINES CP,CP,AP,IP
specifies that processor engines 0 and 1 are of type CP, engine 2 is
type AP, and engine 3 is type IP.
ENGINES 4*CP,2*AP,2*IP
specifies that the first four processor engines (engines 0-3) are of
type CP, the next two (engines 4-5) are of type AP, and the next two
(engines 6-7) are of type IP.
The number of installed processor engines is determined by the MAXCPU statement. If the ENGINES statement specifies more than MAXCPU engines, the excess engines are ignored. If fewer than MAXCPU engines are specified, the remaining engines are set to type CP.
HERCPRIO nn
Specifies the process priority for Hercules. The default is 0. See "Process Priorities" below for more information.
HTTP PORT nnnn [[NOAUTH] | [AUTH userid password]]
Specifies the port number (in decimal) on which the HTTP server
will listen. The port number must either be 80
or within the range 1024 - 65535 inclusive. The server is not start until a subsequent
HTTP START statement is found.
AUTH indictates that a userid and password are required to access the HTTP server, whereas NOAUTH indicates that a userid and password are not required. The userid and password may be any valid string.
Note: HTTPPORT nnnn [[NOAUTH] | [AUTH userid password]] is still supported,
however, it has been deprecated.
HTTP ROOT directory
Specifies the root directory where the HTTP server's files reside. If not specified, the default value for Win32 builds of Hercules is the directory where the Hercules executable itself is executing out of, and for non-Win32 builds it is the directory specified as the default package installation directory when the Hercules executable was built (which can vary depending on how the Hercules package was built, but is usually /usr/local/share/hercules/).
Note: HTTPROOT directory is still supported, however, it has been deprecated.
HTTP START
Starts the HTTP server. (Note: The server is no longer started by default.)
IGNORE INCLUDE_ERRORS
Indicates that errors caused by subsequent
INCLUDE statements
for files which do not exist should instead be ignored rather
than causing startup to be aborted (as would otherwise normally
occur).
INCLUDE filepath
An INCLUDE statement tells Hercules configuration file
processing to treat the contents of the file specified by filepath
as if its contents had appeared in the configuration file at the point
where the INCLUDE statement appears.
Note that the included file may itself contain yet another
INCLUDE statement as long as the maximum nesting depth
(current 8) is not exceeded.
IODELAY usec
Specifies the amount of time (in microseconds) to wait after
an I/O interrupt is ready to be set pending. This value can also be
set using the Hercules console. The purpose of this parameter is to
bypass a bug in the Linux/390 and zLinux dasd.c
device driver. The problem is more apt to happen under Hercules than
on a real machine because we may present an I/O interrupt sooner than a
real machine.
NOTE : OSTAILOR LINUX no longer sets
IODELAY to 800 since the problem described above is no longer present in
recent versions of the Linux kernel.
LDMOD module list
Specifies additional modules that are to be loaded by the Hercules dynamic loader. The default search order is with the hercules directory in the default DLL search path. Most systems also support absolute filenames (ie names starting with '/' or '.') in which case the default search path is not taken.
Multiple LDMOD statements may be used.
LEGACYSENSEID OFF | DISABLE | ON | ENABLE
Specifies whether the SENSE ID CCW (X'E4') will be honored for the devices that originally didn't support that feature. This includes (but may not be limited to) 3410 and 3420 tape drives, 2311 and 2314 direct access storage devices, and 2703 communication controllers.
Specify ON or ENABLE if your guest
operating system needs the Sense ID support to dynamically
detect those devices. Note that most current operating systems
will not detect those devices even though Sense ID is enabled
because those devices never supported the Sense ID in the first
place. So this mainly applies to custom built or modified versions
of guest operating systems that are aware of this specific Hercules
capability.
Because those legacy devices didn't originally support this command,
and for compatibility reasons, the default is OFF
or DISABLE.
LOADPARM xxxxxxxx
Specifies the eight-character IPL parameter which is used by some operating systems to select system parameters.
LOGOPT TIMESTAMP | NOTIMESTAMP
Sets Hercules log options. TIMESTAMP causes messages to the log to be time stamped. NOTIMESTAMP prevents time stamping of log messages. TIMESTAMP and NOTIMESTAMP may be abbreviated as TIME and NOTIME respectively. The current resolution of the stamp is one second.
The default is TIMESTAMP.
LPARNAME name
Specifies the LPAR name returned by DIAG X'204'. The default is
HERCULES.
LPARNUM xx | BASIC
Specifies the one- or two-digit hexadecimal LPAR identification number stored by the STIDP instruction, or BASIC.
If a one-digit number from 1 to F (hexadecimal) is specified, then STIDP stores a format-0 CPU ID unless a subsequent CPUIDFMT 1 statement is specified. If zero or a two-digit hexadecimal number (except 10 hexadecimal) is specified, then STIDP stores a format-1 CPU ID. For LPARNUM 10 the current CPUIDFMT is not changed. If LPARNUM is BASIC, then STIDP stores a basic-mode CPU ID.
The default is LPARNUM 1 with a format-0 CPU ID.
MAINSIZE nnnn |
nnnK |
nnnM |
nnnG |
nnnT |
nnnP |
nnnE
Specifies the main storage size in megabytes, where
nnnn is a decimal number. Or,
nnnM where M
is
K - Kilobytes,
M - Megabytes,
G - Gigabytes,
T - Terabytes,
P - Petabytes,
E - Exabytes.
The default on startup is 2M.
For storage sizes less than 16M, sizes not on a 4K boundary are rounded up to the next 4K boundary. Otherwise, storage sizes not on a 1M boundary are rounded up to the next 1M boundary.
The minimum size is 4K for archlvl als0 and als1 (S/370 and ESA/390), and 8K for archlvl als2 (ESAME) and higher. A maximum of 64M may be specified for archlvl als0 (S/370), 2048M (2G) for archlvl als1 (ESA/390), and 16E for archlvl als2 (ESAME) and higher.
Notes:
MANUFACTURER name
Specifies the MANUFACTURER name returned the STSI instruction. The default is
HRC.
MAXCPU nn
Specifies the number of installed processor engines. The NUMCPU statement specifies the number of engines which will be configured online at startup time. All processors are CP engines unless otherwise specified by the ENGINES statement.
The value of MAXCPU cannot exceed the value of MAX_CPU_ENGINES.
If MAXCPU is not specified in the Hercules configuration file,
then its initial value is equal to NUMCPU.
If MAXCPU and NUMCPU are both omitted, MAXCPU is set to 1.
MAX_CPU_ENGINES is a compile-time variable which sets
an upper limit on the value of MAXCPU.
The value of MAX_CPU_ENGINES is displayed in the
Build information message on the Hercules control panel at startup time.
To change the value of MAX_CPU_ENGINES you must rebuild
Hercules.
For Unix builds, specify
./configure --enable-multi-cpu=nn
before performing make.
For Windows builds, specify
SET MAX_CPU_ENGINES=nn
before performing nmake.
MAX_CPU_ENGINES cannot exceed 64. For performance reasons,
values above 32 are not recommended for 32-bit platforms.
If MAX_CPU_ENGINES is set to 1 then multiprocessing is disabled.
See also NUMCPU for a discussion of the performance
implications of MAX_CPU_ENGINES.
MODEL hardware_model
[ capacity_model ]
[ perm_capacity_model ]
[ temp_capacity_model ]
Specifies the MODEL names returned by the STSI instruction.
If two operands are supplied, the first is the hardware model name (CPC ND model) and the second is the capacity model name (CPC SI model). If only one operand is supplied, it is used as both the hardware model name and the capacity model name. The optional third and fourth operands specify the permanent capacity model name and the temporary capacity model name respectively.
The default is EMULATOR.
MODPATH path
Specifies the path where dynamic modules are loaded from. When a modpath statement is specified, the path on the modpath statement is searched before the default path is searched. When a relative path is specified is interpreted as a relative path within the default search path, if an absolute path is specified is interpreted as such.
The default MODPATH is hercules, which means modules are loaded from the directory hercules within the default LD_LIBRARY_PATH.
MOUNTED_TAPE_REINIT DISALLOW | DISABLE | ALLOW | ENABLE
Specifies whether reinitialization of tape drive devices (via the
devinit command, in order to mount a new tape) should
be allowed if there is already a tape mounted on the drive.
Specifying ALLOW|ENABLE (default) indicates new tapes may
be mounted (via 'devinit nnnn new-tape-filename')
irrespective of whether or not there is already a tape mounted on the drive.
Specifying DISALLOW|DISABLE prevents new tapes from being mounted
if one is already mounted. When DISALLOW is specified
and a tape is already mounted on the drive, it must first be unmounted
(via the command 'devinit nnnn *') before
the new tape can be mounted. Otherwise the devinit attempt to mount
the new tape is rejected.
This option is meant as a safety mechanism to protect against accidentally dismounting a tape from the wrong drive as a result of a simple typo (thereby cancelling a potentially important tape job) and was added by user request.
Also note that for SCSI tape drives the 'devinit nnnn *'
command has no effect as the tape must be unmounted manually (since it is
a real physical device and not one emulated via a disk file like .AWS tapes).
NUMCPU nn
Specifies the number of emulated processor engines which will be configured online at startup time. NUMCPU cannot exceed the value of MAXCPU. If NUMCPU is less than MAXCPU then the remaining engines can be configured online later. The default NUMCPU value is 1. The minimum value is 0.
Multiprocessor emulation works best if your host system actually has more than one physical CPU, but you can still emulate multiple CPUs nervertheless even on a uniprocessor system (and you might even achieve a small performance benefit when you do). There is little point, however, in specifying NUMCPU greater than 1 unless your guest operating system (running under Hercules) is actually able to support multiple CPUs (and if you do not actually need multiprocessor emulation, then setting MAX_CPU_ENGINES to 1 at compile time might even produce a slight performance advantage too).
NUMVEC nn
Specifies the number of emulated vector facilities. Default is one per CPU. Only available by default in ESA/390 mode.
OSTAILOR OS/390 | z/OS |
VM | VSE | z/VSE | LINUX | OpenSolaris | QUIET | NULL
Specifies the intended operating system. The effect of this
parameter is to reduce control panel message traffic by
selectively suppressing trace messages for program checks
which are considered normal in the specified environment.
QUIET discards all exception messages.
NULL allows all exception messages to be logged.
Optionally prefix any value except QUIET or
NULL with '+' to cause the suppressions for that
environment to be combined (added) to those already specified,
or with '-' to remove such suppressions (i.e. to allow them).
If the OSTAILOR
statement is omitted, exception messages for program checks
10, 11, 16, and 1C are suppressed.
Use the ostailor or pgmtrace panel
commands to display or alter the current settings.
PANRATE SLOW | FAST | nn
Specifies the panel refresh rate, in milliseconds between refreshes. SLOW is the same as 500, and FAST is the same as 50. A value less than the Linux system clock tick interval (10 on Intel, 1 on Alpha), or more than 5000, will be rejected. SLOW is the default.
PANTITLE "title-string"
Specifies an optional console window title-bar string to be used in place of the default supplied by the windowing system. If the value contains any blanks it must be enclosed within double-quotes.
This option allows one to distinguish between different Hercules sessions when running more than one instance of Hercules on the same machine.
This option takes effect only when the Hercules console is displayed on an xterm terminal (commonly used on Unix systems), or in a Windows command prompt window. Note that this option has no effect when Hercules is run under control of the Hercules GUI since Hercules's console window is hidden in favor of using the GUI's window instead.
PGMPRDOS RESTRICTED | LICENSED
Specifies whether or not Hercules will run licensed program product ESA
or z/Architecture operating systems. If RESTRICTED is
specified, Hercules will stop all CPUs when a licensed program product
operating system is detected. Specify
LICENSED to allow these operating systems to run normally.
This parameter has no effect on Linux/390, Linux for z/Series, or any
370-mode OS.
NOTE: It is YOUR responsibility to comply with the terms of the license for the operating system you intend to run on Hercules. If you specify LICENSED and run a licensed operating system in violation of that license, then don't come after the Hercules developers when the vendor sends their lawyers after you.
RESTRICTED is the default. Specifying
LICENSED will produce a message when a licensed operating
system is detected to remind you of your responsibility to comply with
software license terms.
PLANT name
Specifies the PLANT name returned by the STSI instruction. The default is
ZZ.
SCSIMOUNT NO | YES | nn
Specifies whether automatic detection of SCSI tape mounts are to be enabled or not.
Specifying NO or 0 seconds (the default) indicates
the option is disabled, forcing all SCSI tape mounts to be done
manually via an appropriate devinit command.
A value from 1 to 99 seconds inclusive enables the option
and causes periodic queries of the SCSI tape drive to automatically
detect when a new tape is mounted. Specifying YES
is the same as specifying 5 seconds.
The scsimount panel command may also be used to display
and/or modify this value on demand once Hercules has been started. Note
too that the scsimount panel command also lists any mounts
and/or dismounts that may still be pending on the drive, as long as
you've defined your tape drive as a model that has an LCD "display"
(such as a model 3480, 3490 or 3590).
Note: enabling this option may cause Hercules to take longer to shutdown depending on the value specified for this option as well as how the host operating system (Windows, Linux, etc) and associated hardware (SCSI adapter) behaves to drive status queries for drives which do not have any media currently mounted on them.
SHCMDOPT DISABLE | NODIAG8
When set to DISABLE, sh (shell) commands are globally disabled, and will result
in an error if entered either directly via the Hercules hardware console or
programmatically via the DIAG8CMD interface.
When set to NODIAG8 only the programmatic execution of shell commands via the
the Diagnose 8 interface is disabled, but sh (shell) commands entered directly
via the Hercules hardware console will still work.
NOTE: "entered directly via the Hercules hardware console" also pertains to both commands entered via the HTTP server facility as well as commands entered via .rc "run command" scripts.
SHOWDVOL1 [ NO | YES | ONLY ]
Indicates whether to show the dasd VOL1 labels (volser) in the device list display. 'YES' shows the volser in addition to the usual filename, whereas 'NO' shows the device list in a traditional filename only format. The 'ONLY' option shows only the volser; the filename is not shown at all. The default is 'NO', which results in a traditional device list display. This statement has no effect when no operand is given and instead simply echos the current setting to the console.
Note: support for this command/statement must be specifically
generated by enabling the #define OPTION_SHOWDVOL1
statement in source header 'featall.h' and then rebuilding Hercules.
SHRDPORT nnnn
Specifies the port number (in decimal) on which the Shared Device server
will listen. Specifying SHRDPORT will allow other Hercules instances
to access devices on this instance. (Currently only DASD devices may
be shared). By default, the other Hercules instances (clients) will
use port 3990. If you specify a different port number, then you will
have to specify this port number on the device statement for the other
Hercules clients.
If no SHRDPORT statement is present then the Shared Device server thread
will not be activated.
SRVPRIO nn
Specifies the priority of the server threads. The default value is 4. See "Thread Priorities" below for more information.
Caution: SRVPRIO should not have a higher dispatching priority than the TOD Clock and timer thread.
SYSEPOCH yyyy [±years]
Specifies the base date for the TOD clock. Use the default value
(1900) for all systems except OS/360. Use 1960
for OS/360. Values other than these were formerly used to offset the
TOD clock by a number of years to move the date before the year 2000 for
non-Y2K-compliant operating systems. This use is deprecated, and support
will be removed in a future release; at that time, only values of
1900 or 1960 will be accepted. Other values
will produce a warning message with the equivalent values to specify in
the SYSEPOCH statement.
An optional year offset may be specified, and will be treated as though
it had been specified on a YROFFSET
statement.
TIMERINT DEFAULT | nnnn
Specifies the internal timers update interval, in microseconds. This parameter specifies how frequently Hercules's internal timers-update thread updates the TOD Clock, CPU Timer, and other architectural related clock/timer values. The default interval is 50 microseconds, which strikes a reasonable balance between clock accuracy and overall host performance. The minimum allowed value is 1 microsecond and the maximum is 1000000 microseconds (i.e. one second).
Caution: While a lower TIMERINT value may help increase the accuracy of your guest's TOD Clock and CPU Timer values, it could also have a severe negative impact on the overall performance of your host operating system. This is especially true when a low TIMERINT value is coupled with a high HERCPRIO and TODPRIO priority setting. Exercise extreme caution when choosing your desired TIMERINT in relationship to your chosen HERCPRIO and TODPRIO priority settings.
TODDRAG n.nn
Specifies the TOD clock drag factor. This parameter can be used to slow down or speed up the TOD clock by a factor of nn. A significant slowdown can improve the performance of some operating systems which consume significant amounts of CPU time processing timer interrupts. A drag factor of 2.0 slows down the clock by 50%. A drag factor of 0.5 doubles the speed of the clock. A drag factor of 1.01 slows down the clock by 1%, and 0.99 speeds up the clock by 1%.
TODPRIO nn
Specifies the priority of the TOD Clock and timer thread. The default value is -20. See "Thread Priorities" below for more information.
Caution: TODPRIO should be given a dispatching priority equal to or higher than any other thread within Hercules.
TRACEOPT TRADITIONAL | REGSFIRST | NOREGS
Sets the Hercules instruction tracing display option.
TRADITIONAL (the default), displays the registers following
the instruction about to be executed such that pressing enter (to execute
the displayed instruction) then shows the next instruction to be executed
followed by the updated registers display.
REGSFIRST displays the current register contents followed by
the instruction about to be executed such that pressing enter (to execute
the displayed instruction) then shows the updated registers followed by
the next instruction to be executed.
NOREGS suppresses the registers display altogether
and shows just the instruction to be executed.
In addition to the TRACEOPT configuration file statement
there is also a corresponding traceopt panel command to
dynamically display and/or update the current setting at any time.
TZOFFSET ±hhmm
Specifies the hours and minutes by which the TOD clock will
be offset from the current system time. For GMT, use the
default value (0000). For timezones west of Greenwich, specify
a negative value (example: -0500 for US Eastern Standard
Time, -0800 for US Pacific Standard Time).
For timezones east of Greenwich, specify a positive value
(example: +0100 for Central European Time,
+0930 for South Australian Time).
XPNDSIZE nnnn |
nnnM |
nnnG |
nnnT |
nnnP |
nnnE
Specifies the expanded storage size in megabytes, where
nnnn is a decimal number. Or,
nnnM where M
is K - Kilobytes, M - Megabytes, G - Gigabytes, T - Terabytes,
P - Petabytes, E - Exabytes.
Storage sizes not on a 1M boundary are rounded up to the next 1M boundary. The lower limit and default is 0.
Notes:
YROFFSET ±years
Specifies a number of years to offset the TOD clock from the actual
date. Positive numbers will move the clock forward in time, while
negative numbers will move it backward. A common value for
non-Y2K-compliant operating systems is YROFFSET -28, which
has the advantage that the day of the week and the presence or absence
of February 29 is the same as the current year. This value may not be
specified as greater than ±142 years, the total range of the TOD
clock. Specifying a value that causes the computed TOD clock year to be
earlier than the value of SYSEPOCH
or more than 142 years later than that value will produce unexpected
results.
A comment preceded by a # sign may be appended to any system parameter statement.
In configuration and device statements, as well as in panel commands and OAT files, symbols may be substituted for text.
To substitute symbol symbol with its contents, the symbol should be enclosed within parenthesis and preceded by a $ sign. For example, if symbol FOO contains the text string "BAR" then $(FOO) will be substituted with the string "BAR";. Symbol names are case sensitive.
DEFSYM TAPEDIR "/home/hercules/tapes"
...
0380 3420 $(TAPEDIR)/scratch.aws
...In this example, device 0380 will be a 3420 loaded with the AWS tape file in /home/hercules/tapes/scratch.aws
When multiple devices are defined with a single device definition statement, then the symbols
- CUU
(3 digits device number, upper case hexadecimal digits) - CCUU
(4 digits device number, upper case hexadecimal digits) - DEVN
(4 digits device number, upper case hexadecimal digits)
are defined to contain for each device the relevant device address. For example:
0200,0201 3340 /home/hercules/dasds/myvols.$(CUU)
will define two 3340 packs, with device 0200 being loaded with the file myvols.200 and device 0201 defined with myvols.201.
If a symbol is not explicitly defined by a DEFSYM statement and an environment variable by the same name exists, the string contents of that environment variable will be used for substitution.
If a symbol is not defined by an explicit DEFSYM, is not an automatically generated symbol and is not an environment variable, an empty string will be substituted.
To be able to specify the '$(' string without incurring substitution, an additional '$' sign should be used. For example, $$(FOO) will not be substituted. If substitution is required but the preceding text is to contain a '$' sign as the very last character, then $$$(FOO) should be specified. Thus, if symbol FOO contains "BAR", then $$(FOO) will remain "$$(FOO)" while $$$(FOO) will become "$BAR".
Substitution is not recursive (only one substitution pass is made).
Enhanced symbol substitution differs from the above normal symbol substitution in several very important ways:
First, the syntax is different. Enhanced substitution symbol names are specified
using ${var} (dollar + brace) rather than $(var)
(dollar + parenthesis).
Second, the enhanced syntax supports specifying a default value that is to be used
instead whenever the name symbol is otherwise not defined. The default value is
placed within the opening and closing braces just as the symbol name is, but
separated from it by either a single equal sign '=' or a
colon-equal-sign ':='.
For example, specifying "${DASD_PATH=dasd/}" in your configuration
file requests that the value of the "DASD_PATH" symbol or environment variable be
substituted, or, if the variable is undefined, to use the value "dasd/"
instead. If no default value is specified then an empty string is used instead.
Finally, enhanced symbol substitution occurs only from host defined environment
variables and not from any identically named DEFSYM symbol
should one exist. For example, if environment variable 'FOO' is defined with the
value "bar", then the configuration file statement "DEFSYM FOO myfoo"
followed immediately by the statement "${FOO}" causes the value
"bar" to be substituted and not 'myfoo' as might
otherwise be believed, whereas the statement "$(FOO)", since it is
a normal symbol substitution sequence does get replaced with "myfoo"
(since that was the value defined to it via the preceding DEFSYM
statement).
In other words each symbol substitution technique is supported completely separately
from one another. DEFSYM allows one to define/undefine/use private (internally
defined) symbols separate from the host operating system's environment variable pool,
whereas the enhanced symbol substitution does not and instead only allows read-only
access to the host's environment variable pool with no support for modifying an already
defined symbol (environment variable) but a nonethless convenient means of defining
a default value to be used should the specified host environment variable be currently
undefined.
Further note that symbol names, being the names of environment variables, are subject
to whatever case sensitivity or case insensitivity that the host operating system
happens to enforce/allow. On Windows, environment variables are not case sensitive, whereas on other
operating systems they may be. Thus "${FOO}", "${foo}",
"${Foo}", etc, all cause the same value to be substituted on Windows,
whereas the DEFSYM symbols $(FOO) and $(foo),
being two completely different and unique symbols, could be substituted with two
completely different values (since DEFSYM is
case sensitive across all supported platforms, including Windows).
To substitute symbol symbol with the current environment variable value,
the symbol should be enclosed within braces and preceded by a $ sign. For example,
if an environment variable named FOO holds the value "BAR", then
${FOO} will be substituted with the string "BAR". If the environment variable
"FOO" is not defined then a null (empty) string is substituted instead.
If the string "${FOO:=myfoo}" is used instead, then the value "BAR" will still be
substituted if the value "BAR" was indeed previously assigned to FOO, but will be
substituted with the value "myfoo" instead if the environment variable
FOO is currently undefined.
Note too that the default value is a literal
string and no substitution is applied to it. Thus attempting to use the syntax
"${foo=${bar}}" will not yield the expected results. It will
not be substituted with the currently defined value of the "bar" environment
variable, but rather will always be substituted with the literal string
"${bar" followed immediately by the literal character '}'.
Symbol names (environment variable names) are not case sensitive on Windows whereas they might be on other host operating systems.
Note: Under Linux, a process is a thread and thread priority information applies instead.
For Windows, the following conversions are used for translating Unix process priorities to Windows process priority classes:
| Unix Priority |
Windows Process Priority Class |
Meaning |
|
|---|---|---|---|
| -20 to -16 | Real-time | Process that has the highest possible priority. The threads of the process preempt the threads of all other processes, including operating system processes performing important tasks. For example, a real-time process that executes for more than a very brief interval can cause disk caches not to flush or cause the mouse to be unresponsive. | |
| -15 to -9 | High | Process that performs time-critical tasks that must be executed immediately. The threads of the process preempt the threads of normal or idle priority class processes. An example is the Task List, which must respond quickly when called by the user, regardless of the load on the operating system. Use extreme care when using the high-priority class, because a high-priority class application can use nearly all available CPU time. | |
| -8 to -1 | Above Normal | Process that has priority above the Normal class but below the High class. | |
| 0 to 7 | Normal | Process with no special scheduling needs. | |
| 8 to 14 | Below Normal | Process that has priority above the Idle class but below the Normal class. | |
| 15 to 20 | Idle | Process whose threads run only when the system is idle. The threads of the process are preempted by the threads of any process running in a higher priority class. An example is a screen saver. The idle-priority class is inherited by child processes. |
Caution: On Windows, the value you choose for your Process Priority has a direct impact on how your Thread Priorities are interpreted! You should never modify one without understanding what impact your doing so might have on the other!
On a Linux/Unix host, Hercules needs to be a setuid root
program to allow it to reset its dispatching priority to a high
(negative) value
(i.e., chown root.root hercules; chmod +s hercules).
For Windows, the following conversions are used for translating Linux/Unix thread priorities to Windows thread priorities:
| Unix Priority |
Windows Thread Priority |
Meaning |
|
|---|---|---|---|
| -20 to -16 | Time Critical | Base priority of 15 for Idle, Below Normal, Normal, Above Normal, or High class processes, and a base priority of 31 for Realtime class processes. | |
| -15 to -9 | Highest | Priority 2 points above the priority class. | |
| -8 to -1 | Above Normal | Priority 1 point above the priority class. | |
| 0 to 7 | Normal | Normal priority for the priority class. | |
| 8 to 14 | Below Normal | Priority 1 point below the priority class. | |
| 15 to 19 | Lowest | Priority 2 points below the priority class. | |
| 20 | Idle | Base priority of 1 for Idle, Below Normal, Normal, Above Normal, or High class processes, and a base priority of 16 for Realtime class processes. |
Caution: On Windows, your Thread Priority is interpreted differently based on your chosen Process Priority setting! You should never modify your Thread Priority settings without first reviewing your chosen Process Priority setting!
The remaining statements in the configuration file are device statements. There must be one device statement for each I/O device or group of identical I/O devices. The format of the device statement is:
devnum(s) devtype [ arguments ] [ # comments... ]
where the generic syntax for device numbers is
[n:]CCUU[,CCUU][-CCUU][.nn][...]
as explained below:
devnum(s)is either a single devnum, a range of devnums (separated by a '-' (dash)), a count of devnums (separated by a '.' (dot/period/stop)), or a comma separated list of devnums. Examples would be 200-210 or 0300.10 or 0400,0403 or 0100,0110-011F.
All devices defined when devnums specifies more than one device have identical characteristics (except for the device number itself). All devices defined as a group must be defined on a single channel. A channel is defined as a contiguous group of 256 (or hexadecimal 100) devices. 0010 and 0020 are on the same channels. 0100 and 0210 are not.
See devnum immediately below for an explanation of how each device number is specified.
The 4 special subtitution symbols CUU, CCUU, cuu and ccuu are also defined for each device in a device group. See substitutions for details.
devnumis either a 1 to 4 digit hexadecimal number in the range 0000 to FFFF for ESA/390, or 0000 to 0FFF for S/370. The device number uniquely identifies each device to the operating system.
Channel Set / Logical Channel SubsystemAn optional Channel Set or Logical Channel Subsystem Identification can be specified for a device number or group of devices. The Identification number is specified at the beginning of the definition, followed by a ':' character. For example :
1:0400-040F 3270
defines 3270 devices 400 to 40F to be on S/370 Channel Set 1 or on S/390 or z/Architecture Logical Channel Subsystem # 1.
Since each Logical Channel Subsystem defines its own device numbering space, care should be taken in S/370 mode as to define a coherent set of device numbers.
Not all S/390 or z/Architecture operating systems support Multiple Logical Channel Subsystems (this feature was introduced with the z9-109).
If no Channel Set or Logical Channel Subsystem Identification is specified, then it is assumed to be 0.
devtypeis the device type. Valid device types are shown in the table just below.
argumentsis a list of parameters whose meaning depends on the device type. The arguments required for each class of device are shown further below.
# comments...A comment preceded by a # sign may be appended to any device definition statement.
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||
There are no required arguments for this particular device type, but there are however several optional arguments which are discussed below.
To use this device, a tn3270 client must connect to the host machine via the port number specified on the CNSLPORT statement. A valid tn3270 device type, such as IBM-3278, must be used. See the Telnet/tn3270 Console How-To for additional information about setting up a tn3270 client.
If your tn3270 client software allows you to specify a device type suffix
(e.g. IBM-3278@001F ), then you can use the suffix to connect
to that specific device number, if eligible. If no suffix is specified,
then your client will be connected to the first available 3270 device for
which it is eligible, if any.
If you specify a specific terminal device address (via the device type suffix of your tn3270 client software), then you must be eligible to connect at that device address or your connection is immediately rejected; an alternative terminal device for which you might be eligible is not automatically selected instead.
Optional arguments:
groupname
If a terminal group name is given on the device statement, a device type
suffix with this group name can be used to indicate that a device in this
group is to be used. If a group name is specified as a terminal type suffix
(e.g. IBM-3278@GROUPNAME ) and there are no devices defined
for that group (or there are no more available devices remaining in that
group), then the connection is rejected. If no group name is specified
as a terminal type suffix, then the connection will only be eligible for
any terminal devices which do not have a group name specified on
their device statements. The terminal group name, if specified, should
be 1 to 8 alphanumeric characters, the first character being alphabetic,
and it should not be a hexadecimal number. Upper and lower case
letters in the group name are considered to be equivalent.
ipaddr [ mask ]
The optional IP address and optional subnet mask specify the IP address(es) of which client(s) are allowed to connect at the device address identified by the device statement on which they appear. This provides an alternative and/or additional means of specifying to which device(s) a client tn3270 session may, or should, connect.
If the IP address of the tn3270 client trying to connect, when 'and'ed with the optional subnet mask (which defaults to 255.255.255.255 if not specified), matches the IP address entered on the device statement, then the client is eligible to connect at that device address. Otherwise the client is ineligible to connect at that address and the next available device, if any, for which the client is eligible to connect (if any) is selected instead.
If no permissible terminal devices remain (i.e. terminal devices for which the client is eligible to connect), or there are no more available terminal devices remaining, then the client connection is rejected.
The optional IP address and subnet mask may also be specified in conjunction with the previously mentioned terminal group argument, but the terminal group argument, if specified, must be specified ahead of (i.e. before) the optional IP address and subnet mask arguments. To specify an IP address and subnet mask without also specifying a terminal group, simply use '*' as the group name instead.
If an IP address / subnet mask are not specified, then any client tn3270 session is allowed to connect to the device (provided they are also a member of the specified terminal group, if any).
The terminal group name argument, if specified, always takes precedence over any optional IP address and subnet mask which may also be specified.
The integrated 3270 (SYSG) console is similar to a local non-SNA 3270 device, except that it is not addressed by subchannel number and it is supported only by certain system control programs. The SYSG console is defined like a 3270 device except that the device type is SYSG and the device number is ignored. Only one SYSG console can be defined in a configuration.
Use tn3270 client software to connect to the SYSG console device via the port number specified on the CNSLPORT statement, just as you would connect to a regular local non-SNA 3270 device. See the Telnet/tn3270 Console How-To for additional information about setting up a tn3270 client.
The SYSG console configuration statement recognizes optional arguments which specify group name and IP address in the same way as previously described for a local non-SNA 3270 device. These optional arguments provide a means to ensure that a given tn3270 client can connect directly to the SYSG console. If the group name and IP address arguments are not specified, then the SYSG console is considered to be a member of the general pool of devices eligible for connection to any incoming tn3270 client.
There are two optional arguments: the command prefix argument and the
optional noprompt argument.
Since integrated console printer-keyboard devices use the Hercules HMC panel (Hardware Management Console) for all input and output, the command prefix is needed so Hercules can distinguish between input meant for the device and normal Hercules panel command input.
All integrated console devices must use a different command prefix and must not be a subset or superset of any other device's command prefix. If one is not specified then the next available default is chosen from the following list:
Hex Glyph Description
0x2F / slash (default)
0x5C \ backslash
0x60 ` backtick
0x3D = equals
0x7E ~ tilde
0x40 @ at sign
0x24 $ dollar
0x25 % percent
0x5E ^ caret
0x26 & ampersand
0x5F _ underline
0x3A : colon
0x3F ? question
0x30 0 zero
0x31 1 one
0x32 2 two
0x33 3 three
0x34 4 four
0x35 5 five
0x36 6 six
0x37 7 seven
0x38 8 eight
0x39 9 nine
If your command prefix was the '/' slash character for example, then to send a logon command to a 1052-C or 3215-C device, you would enter "/logon" on the Hercules console. Or, if your command prefix was "foo=" then you would enter "foo=logon", etc.
When your guest operating system writes a message to an integrated console printer-keyboard device, the message displayed on the Hercules console is always prefixed with the device's command prefix string so you can distinguish it from messages written by other integrated console devices and/or Hercules itself.
The second optional argument for integrated console printer-keyboard devices
is the noprompt keyword. If not specified, then whenever the
system is awaiting input on that device, the prompting message "Enter input
for console device nnnn" is displayed on the Hercules console. The
noprompt option suppresses this prompting message.
There are no required arguments for this particular device type, but there are however several optional arguments discussed below.
To use this device, a telnet client must connect to the host machine via the port number specified on the CNSLPORT statement. See the Telnet/tn3270 Console How-To for additional information about setting up a telnet or tn3270 client.
If your telnet client software allows you to specify a device type suffix
(for example: ansi@0009 ), then you can use that suffix to specify
the specific 1052 or 3215 device to which you wish to connect. If you do not
specify a suffix in your telnet client software (or your software does not
allow it), then your client will be connected to the first available 1052 or
3215 device for which it is eligible.
An optional noprompt argument may be specified on the device
statement to cause suppression of the "Enter input for console device nnnn"
prompt message which is otherwise normally issued to the device whenever
the system is awaiting input on that device.
Additionally, a terminal group name, IP address and subnet mask may all also be optionally specified in the exact same manner as discussed in the previous Local non-SNA 3270 devices section with the exception that the "noprompt" option, if specified, must precede the other arguments.
The argument specifies a list of file names containing card images. Additional arguments may be specified after the file names:
sockdev
Indicates the card reader is a socket device wherein the
filename is actually a socket specification instead of a
device filename. When used, there must only be one filename
specified in the form: port or host:port
or sockpath/sockname. The device then accepts
remote connections on the given TCP/IP port or Unix Domain
Socket, and reads data from the socket instead of from a device
file. This allows automatic remote submission of card reader
data. See the Hercules Socket Reader
page for more details.
eof
Specifies that unit exception status is presented after
reading the last card in the file. This option is persistent, and
will remain in effect until the reader is reinitialized with the
intrq option.
intrq
Specifies that unit check status with intervention required
sense bytes is presented after reading the last card
in the file. This option is persistent, and will remain in
effect until the reader is reinitialized with the eof
option.
multifile
Specifies, when multiple input files are entered, to automatically open the next input file and continue reading whenever EOF is encountered on a given file. If not specified, then reading stops once EOF is reached on a given file and an attention interrupt is then required to open and begin reading the next file.
ebcdic
Specifies that the file contains fixed length 80-byte EBCDIC records with no line-end delimiters.
ascii
Specifies that the file contains variable length lines of ASCII characters delimited by LF (line feed) sequences or CRLF (carraige return line feed) sequences at the end of each line.
If neither EBCDIC nor ASCII is specified, then the device handler attempts to detect the format of the card image file when the device is first accessed. Auto-detection is not supported for socket devices, and the default is ASCII if sockdev is specified.
trunc
Specifies, for ASCII files, that lines longer than 80 characters are truncated instead of producing a unit check error.
autopad
Specifies, for EBCDIC files, that the file is automatically padded to a multiple of 80 bytes if necessary.
The argument specifies the name of a file to which the punched output will be written. Additional arguments may be specified after the file name:
ascii
Specifies that the file will be written as variable length
lines of ASCII characters delimited by line feeds or
carriage return line feed sequences at the end of each line.
Trailing blanks are removed from each line.
If the ascii argument is not specified, the
file is written as fixed length 80-byte EBCDIC records with
no line-end delimiters.
crlf
Specifies, for ASCII files, that carriage return line feed
sequences are written at the end of each line.
If the crlf argument is not specified, then
line-feeds only are written at the end of each line.
noclear
Specifies that the output file will not be cleared to zero
bytes when it is opened.
If the noclear argument is not specified, then
any previous content of the file is destroyed when the file
is opened for output.
The argument specifies the name of a file to which the printer output will be written. The output is written in the form of variable length lines of ASCII characters delimited by line feeds or by carriage return line feed sequences. Trailing blanks are removed from each line. Carriage control characters are translated to blank lines or ASCII form feed characters. If the file exists it will be overwritten.
Additional arguments may be specified after the file name:
sockdev
Indicates the line printer is a socket device wherein the
filename is actually a socket specification instead of a
device filename. When used, there must only be one filename
specified in the form: port or host:port.
The device then accepts
remote connections on the given TCP/IP port,
and writes data to the socket instead of to a device
file. This allows automatic remote spooling of line printer
data. The sockdev option is mutually exclusive with all other
printer options (e.g. crlf, etc) and must be specified alone.
crlf
Specifies, for ASCII files, that carriage return line feed
sequences are written at the end of each line.
If the crlf argument is not specified, then
line-feeds only are written at the end of each line.
noclear
Specifies that the output file will not be cleared to zero
bytes when it is opened.
If the noclear argument is not specified, then
any previous content of the file is destroyed when the file
is opened for output.
fcbcheck
Specifies that an attempt to skip to a FCB channel for which no line number has been set will cause the command to be rejected with a unit check. This is the default.
nofcbcheck
Specifies that an attempt to skip to a FCB channel for which no
line number has been set will cause the next line of output to be
printed on the next line on the printer output. The opposite,
fcbcheck, is the default.
rawcc
Specifies that printer output CCWs are not to be interpreted, but simply dumped in hex to the printer output file. This is useful for debugging. Default is to interpret printer CCWs normally.
fcb=
Specifies an initial FCB image to use for this printer. The argument
must be exactly 26 digits long, and consist of digits from 0 to 9.
The first pair of digits specifies the number of lines on a printed
page. It is followed by 12 pairs of digits which specify, for FCB
channels 1-12, the line number on the page that the FCB channel
corresponds to. Use 00 to leave the line number unset
for a channel (see fcbcheck above). The default is
fcb=66010713192531374361495561.
If the filename begins with the vertical bar '|' pipe character, then it is removed and the remainder of the filename is interpreted as a command line (the name of a program or batch file followed by any necessary arguments) to which to "pipe" the printer output to. This is known as the "print-to-pipe" feature. All printer output is then sent to the piped program's stdin input, and all of the piped program's stdout and stderr output is piped back to Hercules for displaying on the hardware console.
If the "print-to-pipe" command line contains arguments, then quotes must be placed around the entire filename string including the vertical bar, for example:
000E 1403 "|/usr/bin/lpr -Phplj" crlf (for Unix)
000E 1403 "|c:\utils\pr -s -PLPT1:" crlf (for Windows)
The above example uses the pr program downloaded
from
http://www.atnetsend.net/computing/
If the "print-to-pipe" command line itself contains quotes, then the command line must be enclosed in apostrophes instead of quotes, for example:
000E 1403 '|"c:\Program Files\My Utils\pr" -s -PLPT1:' crlf
Tim Pinkawa has an example which shows how the print-to-pipe feature can be used to create output in PDF format: http://www.timpinkawa.net/hercules/prtspool.html
Five types of tape emulation are supported (see further below): AWS, HET, FakeTape, Optical Media Attach (OMA), and real SCSI .
The only required parameter is the device filename. All other parameters are optional and must follow the filename. Use '*' (asterisk) for the filename to specify an empty (unmounted) tape drive. The specified file, if other than '*', must exist.
Additionally, if the file name starts with the '@' character (at sign), the file really describes a list of tape emulation files to be loaded in succession.
The syntax of each line is identical to the information that can be specified after the device type when the options are specified directly after the device type in the configuration file.
If the emulation file filename in the file list is the '*' (asterisk) character, then this specifies a set of options to be applied to all additional emulation files specified in the file list.
Parameters are appended in succession. In all cases, if the same parameter is specified more than once, the last instance takes precedence.
Therefore, it is possible to specify a set of parameters in the base configuration file, another set on a '*' line, and another set for each individual line. Parameters are then appended in that order: options specified on the base device statement itself first, followed by those options specified on the '*' statement, and finally those specified on each individual file list statement last. A SCSI tape device should not be given in a file list.
Refer to the distributed source-code's "README.TAPE" document for additional information regarding system and application programming for tape devices and instructions regarding use of the emulated ACF (Automatic Cartridge Feeder) and AUTOMOUNT features for virtual (non-SCSI) tape devices.
These contain a complete tape in one file. AWSTAPE files
consist of variable length EBCDIC blocks. Each block is
preceded by a 6-byte header. Filemarks are represented by
a 6-byte header with no data. This is the same format as is
used by the P/390.
The argument specifies the location of the AWSTAPE file
(for example ickdsf.aws)
These contain a complete tape in one file. FakeTape files
consist of variable length EBCDIC blocks. Each block is
preceded by a 12-ASCII-hex-character header. Filemarks are represented by
a 12-character header with no data. The FakeTape format is
used by the Flex-ES system from Fundamental Software Inc (FSI).
The argument specifies the location of the FakeTape file
(for example ickdsf.fkt). Note: "FLEX-ES" and
"FakeTape" are trademarks of Fundamental Software, Inc.
These contain a complete tape in one file and have the same
structure as the AWSTAPE format with the added ability to have
compressed data.
The first argument specifies the location of the HET file. The
filename must end with ".het" to be recognized by Hercules as an
HET file.
(for example 023178.het)
Additional arguments that allow you to control various HET settings are:
AWSTAPE
The AWSTAPE argument causes HET files to
be written in AWSTAPE format. This basically, disables
the additional features provided by the HET format.
COMPRESS=n
IDRC=n
COMPRESS and IDRC control
whether compression should be used when writing to HET
files. The value n can be 1
to turn on compression (the default) or 0 to turn
it off. IDRC is currently a synonym for
COMPRESS, but may be used in the future to
control other emulated tape drive features.
METHOD=n
The METHOD option allows you to specify
which compression method to use. You may specify
1 for ZLIB compression or 2
for BZIP2 compression. The default is 1.
LEVEL=n
The LEVEL option controls the level of
compression. It ranges from 1 for fastest
compression to 9 for best compression.
The default is 4.
CHUNKSIZE=nnnnn
The CHUNKSIZE option allows you to create
HET files that contain different chunk sizes. The AWSTAPE
(and therefore the HET) format allows each tape block to be
logically broken up into smaller chunks. For instance, if
your S/3x0 application creates tapes with a block size of
27998, those blocks would be broken down into
nnnnn sized chunks.
The range is from 4096
to 65535, the latter being the default.
Decreasing the value from its default may reduce compression
performance.
For compatability with AWSTAPE files created by the P/390,
specify AWSTAPE with CHUNKSIZE=4096.
MAXSIZE=n[s] | MAXSIZEK=n
| MAXSIZEM=n
Specifies the maximum size (in bytes, Kilobytes or Megabytes) that the emulated file is allowed to grow to.
Or, nnns where s is either K - KILO, M - MEGA, G - GIGA, or T - TERA - BYTES
Specifying zero for this parameter means "unlimited" (i.e. there is no limit). Note: "T" is not available on all platforms.
EOTMARGIN=n[s]
Specifies the number of bytes remaining before reaching maxsize at which point the tape device will signal the presence of the "End of Tape" marker (reflector), thus allowing the program to switch to the next tape.
Value is either n = bytes, or ns where s is either a K, M, G, or T multiplier.
READONLY=n
Specifies whether the tape is mounted read-only (without a write ring or with the cartridge protect switch set to "write protect"). A parameter of 1 means read-only; a parameter of 0 means read-write. If READONLY=1, RO or NORING is not specified, the default is READONLY=0. Note that READONLY=0 does not override the host system file permission settings for the underlying AWS or HET file. If the AWS or HET file is marked read-only, the tape will be mounted read-only despite specification of READONLY=0.
RO
NORING
Specifies that the tape is mounted read-only (without a write ring or with the cartridge protect switch set to "write protect"). RO and NORING are equivalent to READONLY=1.
RW
RING
Specifies that the tape should be mounted read-write, if possible. RW and RING are equivalent to READONLY=0. This is the default if RO, NORING or READONLY=1 is not specified. Note that RW and RING do not override the host system file permission settings for the underlying AWS or HET file. If the AWS or HET file is marked read-only, the tape will be mounted read-only despite specification of RW or RING.
DEONIRQ=n
Specifies whether a device end is presented if intervention is required during tape motion. A parameter of 1 selects this option; a parameter of 0 turns it off.
NOAUTOMOUNT
Indicates support for guest-initiated automatic tape volume mounting is to always be disabled for this tape device.
Automatic guest tape-mount support is automatically globally
enabled for all virtual (non-SCSI) tape devices by default
whenever an allowable automount directory is defined via the
AUTOMOUNT configuration file statement
or the automount panel command.
The NOAUTOMOUNT option allows you to specifically
disable such support for a given device.
The automount feature enables software running in guest operating
systems to automatically mount, unmount and/or query for themselves
the host "virtual tape volume" filename mounted on a tape drive,
via the use of special CCW opcodes (0x4B Set Diagnose and 0xE4
Sense Id) without any intervention on the part of the Hercules
operator. An example of such a program for DOS/VSE called
TMOUNT is provided in the util
subdirectory of the distributed source code.
This is a sticky option. When specified, automount support for
the device remains disabled until the option is specifically
removed via a devinit command without the option
specified. This means if NOAUTOMOUNT is enabled
for a device while global automount functionality is currently
disabled (because no AUTOMOUNT statement
was specified at Hercules startup), then automount functionality
remains disabled for the device even should global automount
functionality be later manually enabled via an
automount panel command.
When the 0x4B Set Diagnose CCW is used to auto-mount a virtual tape volume onto a given tape drive, an absolute (fully-qualified) pathname should normally always be specified, but need not be if a path relative to the currently defined "default allowable" automount directory is used instead.
The default allowable automount directory is always the first "allowable" directory that was defined, or else the current directory if no allowable directories were specifically defined. (There is always a default allowable directory whenever any allowable or unallowable automount directories are defined.)
Fully-resolved, absolute-full-path filenames are defined as being those which, for Windows, have a ':' (colon) in the second position or, for other host operating systems (e.g. Linux), have a '/' (slash) in the first position. Paths which start with a '.' (period) are considered relative paths and will always be appended to the currently defined default allowable automount directory, before being resolved into fully-qualified paths by the host system. (I.e. only fully-resolved absolute pathnames are used in the performance of the actual automatic tape volume mount.)
For example, if more than one allowable automount directory is defined and the volume wishing to be mounted happens to reside in the second one, then a fully-qualified absolute pathname should of course be specified (or else one that is relative to the default directory which happens to resolve to the desired file).
All attempts to automount host files in a "disallowed" directory or any of its subdirectories will be rejected. Similarly any attempt to automount a file which is not within any "allowable" directory or subdirectory will be rejected. An error message is always issued in such cases. A message is also issued whenever a successful mount or unmount is performed.
A sample guest automount program called TMOUNT for
the DOS/VSE operating system is provided in the
util subdirectory of the distributed source code.
These are read-only files which usually reside on CDROM.
OMA virtual tapes consist of one CDROM file corresponding
to each physical file of the emulated tape. An ASCII text
file called the tape descriptor file (TDF) specifies the
names of the files which make up the virtual tape.
The argument specifies the name of the tape descriptor
file (for example /cdrom/tapes/uaa196.tdf)
Each file on the virtual tape can be in one of three formats:
TEXT
TEXT files consist of variable length ASCII records delimited by carriage return line feed sequences at the end of each record. Each record is translated to EBCDIC and presented to the program as one physical tape block.
FIXED nnnnn
FIXED files consist of fixed length
EBCDIC blocks of the specified length
(nnnnn)
HEADERS
HEADERS files consist of variable length EBCDIC blocks. Each block is preceded by a 12-byte header.
If you have any IBM manuals in Bookmanager format on CDROM,
you can see some examples of TDF files in the
\TAPES directory on the CDROM.
These are real tape drives attached to the host machine via a SCSI interface. Hercules emulation always makes the drive appear as a channel attached device such as 3420 or 3480, although the underlying physical drive may be any type of SCSI attached tape drive, including 4mm or 8mm DAT, DLT, SCSI attached 3480/3490 cartridge drives, and SCSI attached 3420 open reel tape drives.
Host-attached SCSI tapes are read and written using variable length EBCDIC blocks and filemarks exactly like a mainframe tape volume, and as a result can be freely used/exchanged on either (i.e. SCSI tapes created on a real mainframe can subsequently be read by Hercules just fine, and a SCSI tape created by Hercules can be subsequently read on a mainframe just fine, thus providing a convenient means of exchanging data between the two).
If you plan on using SCSI tapes with Hercules you might also be interested in the SCSIMOUNT configuration option.
The only required device statement parameter for SCSI attached tape
drives is the name of the device as it is known
by the host operating system,
usually "/dev/nst0" (for Linux or
Windows) or "\\.\Tape0" (for
Windows only), where '0' means tape drive number
0 (your first or only host-attached SCSI tape drive), '1' means your
second host-attached SCSI tape drive, etc.
Depending on what actual model of SCSI tape drive you actually have and how it behaves, you may need to specify one or more additional optional parameters for Hercules to provide proper emulation of the desired device type. For example: a Quantum 'DLT' (Digital Linear Tape) SCSI tape drive does not return nor use a block-id format compatible with 3480/3490 drives (it instead uses a full 32-bit block-id just like the model 3590 does). It also does not support the Erase Gap CCW at all.
Thus, in order to use, for example, a Quantum DLT drive with Hercules, you MUST specify some special additional options to prevent the Erase Gap command from being issued to the drive as well as to inform Hercules that the drive uses 32-bit block-ids.
Please note that the below options define how the actual SCSI hardware
device behaves, which is completely different from the way the emulated
device will appear to behave to your guest. That is to say, if you define
your tape drive to Hercules as a 3480 device, then Hercules will perform
3480 device type emulation such that the device appears to your guest o/s
as if it were a 3480 device. If the actual SCSI device behaves as
a 3590 device however (perhaps using/returning 32-bit block-ids instead
of the expected 22-bit format block-ids that 3480's use), then you MUST
specify the --blkid-32 special option on your Hercules device
statement so that Hercules's emulation logic can know that it needs to
translate 22-bit block-ids to 32-bit ones before sending them to the
actual SCSI hardware (and vice versa: to translate 32-bit block-ids from
the actual SCSI drive into 22-bit format block-ids that your guest expects
from a 3480 device).
As explained just above, certain model SCSI tape drives such as the Quantum DLT series may require special handling in order to provide the desired proper device type emulation. These special options are:
--blkid-22
The complete opposite of the below --blkid-32 option.
Use this option if your real SCSI tape drive behaves as a 3480/3490
and expects 22-bit block-ids, but you wish to define the drive to
Hercules as a 3590 tape drive (which uses 32-bit block-ids).
--blkid-32
This option indicates that your SCSI attached tape drive only supports 32-bit block-ids (as used by 3590 drives) and not the 22-bit format used by 3480/3490 drives. You should only specify this option if you intend to define the drive as a model 3480 or 3490 device to Hercules, and then only if your actual real SCSI drive uses 32-bit block-ids.
If you define your Hercules tape drive as a model 3590 device however, then this option is not needed since model 3590 drives are already presumed to use 32-bit block-ids.
Specifying this option on a 3480/3490 device statement will cause Hercules device emulation logic to automatically translate the actual SCSI tape drive's 32-bit block-id into 22-bit format before returning it back to the guest operating system (since that is the format the guest operating system expects it to be in for a model 3480/3490 drive), and to translate the guest's 22-bit format block-id into 32-bit format before sending it to the actual SCSI hardware (since that is the format that the actual hardware requires it to be in).
--no-erg
This option is intended to prevent issuance of the Erase Gap command to those SCSI tape drives which do not support it (such as the Quantum DLT series). It causes Hercules's device emulation logic to ignore any Erase Gap commands issued to the drive and to return immediate 'success' instead.
This option should only be used (specified) for drives such as the Quantum, which support switching from read mode to write mode in the middle of a data stream without the need of an intervening Erase Gap command. Specifying it for any other model SCSI drive may cause incorrect functioning as a result of the Erase Gap command not being issued to the actual SCSI hardware.
Check the manufacturer information for your particular model of SCSI attached tape drive (and/or use Fish's "ftape" Windows utility) to determine whether or not this option is needed for your particular drive.
--online
Use this option if your host's magtape device driver sets the GMT_ONLINE status flag to report when a tape is mounted instead of the more common behavior of clearing the GMT_DR_OPEN flag.
Debian 8.3 Linux systems running on HP (Hewlett Packard) hardware
using StorageTek 9840 fiber channel drives or DEC TSZ07 9-track
drives (via a fc/SCSI bridge) for example, are known to not
use the GMT_DR_OPEN flag at all. Rather, they set the GMT_ONLINE
status flag to indicate when a tape is mounted, thus requiring the
--online option to work properly with Hercules.
The first argument defines the emulation type, and the remaining arguments depend on the chosen emulation type. If the first argument is not a recognized emulation type, then the driver will operate as in Hercules Version 1, using Willem Konynenberg's vmnet package, as described in Axel Schwarzer's CTCA 3088 document.
The following are the emulation types currently supported:
A point-to-point IP connection with the TCP/IP stack of the driving system on which Hercules is running. See the Hercules TCP/IP page for unix details, in particular the use of preconfigured interfaces.
The Windows implementation is different from the unix one. See Fish's CTCI-WIN page for further details and information.
For unix systems, such as Linux, BSD, and OSX, you may use preconfigured interfaces or you may request Hercules to configure the interface for you. In the first case you must know and supply the name of the interface to use; in the second case the kernel supplies an interface name.
ifname
Specifies the interface name of an
interface that is already configured.
The flag --if may optionally be specified
before the name.
Specify no IP addresses or other arguments as the information is already configured into the interface.
guestip
Specifies the IP address of the guest operating system running under Hercules.
hostip
Specifies the IP address of the host (Linux or Windows) side of the point-to-point link. This may or may not be the same as your system's regular IP address. For Windows, if the host system is configured with DHCP, this should instead be the MAC address of the Ethernet adapter you wish to use to have Hercules communicate with the outside world.
If these arguments are specified, they must precede the required arguments.
-m MAC address or --mac MAC address
where 'MAC address' is the optional hardware address
for your guest's virtual adapter/interface in the format: hh:hh:hh:hh:hh:hh.
The default value is '00:00:5E:nn:nn:nn' where the :nn:nn:nn portion
is constructed from the last 3 octets of the specified
guestip.
Note: The MAC address you specify for this option must be unique
as seen by all other devices on your network. It should never,
for example, be the same as the host adapter MAC address specified
on the -n parameter.
-k kernel-capture-buffer-size
-i tuntap32-i/o-buffer-size
See Fish's CTCI-WIN page for further details and information.
If these arguments are specified, they must precede the required arguments:
-n name or --dev name
Specifies the name of the tunnel device to use.
The default
for Linux is /dev/net/tun
(which is correct for version 2.4
and above of the Linux kernel).
The default for OSX is /dev/tun0.
For Windows, specify the IP address or MAC address of the real Windows adapter to emulate the virtual guest's adapter on. The default is the first adapter found according to Windows' adapter binding order, which may not be the one you want if you have multiple adapters.
Refer to the Help file included with Fish's CTCI-WIN product for for more information about adapter binding order and for general information regarding CTCI-WIN configuration.
-s netmask
where netmask is the netmask to use for the automatically added point-to-point route in standard dotted internet noitation (e.g. 255.255.255.0)
-x name or --if name
Specifies the name of the network interface to use.
There is no default for this argument as the kernel assigns an interface name if none is provided.
-d or --debug
Specifies that debugging output is to be produced on the Hercules control panel. This should normally be left unspecified.
An emulated CTCA to another Hercules system. This emulation mode appears to the operating system running in the Hercules machine as an IBM 3088 Channel to Channel Adapter. It provides communication via a TCP connection with another instance of the CTCT driver, and is designed to carry TCP/IP communications between two guest TCP/IP stacks. CTCT may also be used for communication between the client and server components of the MVS Dynamic Debug Tool.
Four arguments are required:
lport
Specifies the local TCP port. This is the TCP port that Hercules will listen on for this CTCA.
rhost
Specifies the remote host. This is the name or IP address of the remote system that Hercules is running on, not the name or IP address of the OS running on that copy of Hercules.
rport
Specifies the remote TCP port. The rport parameter on this system must match the lport parameter on the remote system, and vice versa.
bufsize
Specifies the buffer size for the link. If this link is used for IP traffic, this parameter should be more than the MTU of the interface definition in the OS.
Note: CTCT only supports IP traffic. Use CTCE to transport general purpose payloads such as NJE, SNA, PVM, etc.
The CTCE device type will emulate a real 3088 Channel to Channnel Adapter also for non-IP traffic, enhancing the CTCT capabilities. CTCE connections are also based on TCP/IP between two (or more) Hercules instances, and requires an even-odd pair of port numbers per device side. Only the even port numbers are to be configured; the odd numbers are just derived by adding 1 to the (configured) even port numbers. The socket connection pairs cross-connect, the arrows showing the send->receive direction :
x-lport-even -> y-rport-odd
x-lport-odd <- y-rport-even
Three arguments are required:
lport
raddress
rport
The remaining arguments are optional:
mtu
sml
A sample CTCE device configuration is shown below:
Hercules PC Host A with IP address 192.168.1.100 :
0E40 CTCE 30880 192.168.1.200 30880
0E41 CTCE 30882 192.168.1.200 30882
Hercules PC Host B with IP address 192.168.1.200 :
0E40 CTCE 30880 192.168.1.100 30880
0E41 CTCE 30882 192.168.1.100 30882
CTCE connected Hercules instances can be hosted on either Unix or Windows platforms, both sides do not need to be the same.
An emulated Lan Channel Station Adapter. This emulation mode appears to the operating system running in the Hercules machine as an IBM 8232 LCS device, an IBM 2216 router, a 3172 running ICP (Interconnect Communications Program), the LCS3172 driver of a P/390, or an IBM Open Systems Adapter.
Rather than a point-to-point link, this emulation creates a virtual ethernet adapter through which the guest operating system running in the Hercules machine can communicate. As such, this mode is not limited to TCP/IP traffic, but in fact will handle any ethernet frame.
The configuration statement for LCS is as follows:
NOTE: There are no required parameters for the LCS emulation, however there are several options that can be specified on the config statement:
NOTE: On the MAC OS X Platform, the long option format (--xxx) is not supported. Only the short option format (-x : one dash, one letter) should be used.
-n devname or --dev devname
where devname is:
the name of the TUN/TAP special character device, normally /dev/net/tun.
is either the IP or MAC address of the driving systems network card. Note: If this option is omitted, then TunTap32 automatically selects the first network card it finds, which may not be desirable for some users.
Refer to the Help file included with Fish's CTCI-WIN product for for more information about adapter binding order and for general information regarding CTCI-WIN configuration.
-o filename or --oat filename
where filename specifies the filename of the
OSA Address Table (OAT). If this option is specified, the optional
--mac and guestip entries are ignored in preference to
statements in the OAT. (See further below for the syntax
of the OAT)
If no OAT is specified, the emulation module will create the following:
-m MAC Address or --mac MAC address
where 'MAC address' is the optional hardware address
for your guest's virtual adapter/interface in the format: hh:hh:hh:hh:hh:hh.
The default value is '00:00:5E:nn:nn:nn' where the :nn:nn:nn portion
is constructed from the last 3 octets of the specified
guestip.
Note: The MAC address you specify for this option must be unique
as seen by all other devices on your network. It should never,
for example, be the same as the host adapter MAC address specified
on the -n parameter.
Note: If you use the --oat option, do not specify an address
here. Instead, specify your desired guest adapter MAC address in your OAT
file via the HWADD statement.
guestip
is an optional IP address of the Hercules
(guest OS) side. Note: This is only used to
establish a point-to-point routing table entry
on driving system. If you use the --oat option,
do not specify an address here.
The syntax for the OSA Address Table (OAT) is as follows:
|
Dev
Mode
Note: the SNA operation mode is not currently implemented.
Port
The read/write devices can be swapped by coding the odd address of the even-odd pair in the OAT.
Up to 4 virtual (relative) adapters (i.e. ports) 00-03 are currently supported.
For IP modes, the entry specific information is as follows:
PRI | SEC | NOSpecifies where a packet with an unknown IP address is forwarded to. PRI is the primary default entry, SEC specifies the entry to use when the primary is not available, and NO specifies that this is not a default entry.
nnn.nnn.nnn.nnnSpecifies the home IP address
When the operation mode is IP specify only the read
(even) device number for Dev. The write (odd)
address will be created automatically.
Additionally, a HWADD and/or ROUTE statement may also be included in the OAT:
HWADD pp hh:hh:hh:hh:hh:hhUse the HWADD to specify a hardware (MAC) address for a virtual adapter (port). The first parameter after HWADD specifies the relative adapter (port) to which the address is applied.
ROUTE pp nnn.nnn.nnn.nnn ...The ROUTE statement is included for convenience. This requests Hercules's network configuration logic (hercifc utility on Linux or CTCI-WIN on Windows) to automatically create a network route for this specified virtual adapter. Please note that it is not necessary to include point-to-point routes for each IP address in the table since this is done automatically by the Hercules device driver's emulation module.
A point-to-point IP connection with the TCP/IP stack of the host system on which Hercules is running. From the point of view of the guest image running in the Hercules machine it appears to be an MPCPTP and/or MPCPTP6 ESCON CTC link to another image.
For *nix systems, such as Linux, BSD, and OSX, you may use preconfigured interfaces or you may request Hercules to configure the interface for you. In the first case you must know and supply the name of the interface to use; in the second case the kernel supplies an interface name. See the Hercules TCP/IP page for more details.
-x/--if] ifname
Specifies the interface name of a TUN interface that is already configured.
Specify no host names or IP addresses or other arguments as the information is already configured into the interface.
guest1
Specifies the host name or IP address of the guest operating system running under Hercules.
host1
Specifies the host name or IP address of the host (Linux or Windows) side of the point-to-point link.
guest2
Specifies the host name or IP address of the guest operating system running under Hercules.
host2
Specifies the host name or IP address of the host (Linux or Windows) side of the point-to-point link.
guest1 and host1
must both be of the same address family, i.e. both IPv4 or
both IPv6.
guest2 and host2,
if specified, must both be of the same address family, i.e. both
IPv4 or both IPv6, and must not be of the same address family as
guest1 and host1.
guest1,
and the host name can be resolved to both an IPv4 and an IPv6
address, use either the -4/--inet
or the -6/--inet6 option to
specify which address family should be used;
if neither the -4/--inet nor the
-6/--inet6 option is specified,
whichever address family the resolver returns first will
be used.
host1 or host2 can
be followed by the prefix size expressed in CIDR notation,
e.g. 192.168.1.1/24 or 2001:db8:3003:1::543:210f/48.
For IPv4 the prefix size can have a value from 0 to 32;
if not specified a value of 32 is assumed.
For IPv6 the prefix size can have a value from 0 to 128;
if not specified a value of 128 is assumed.
For IPv4 the prefix size is used to produce the equivalent
subnet mask; for example, a value of 24 produces a subnet
mask of 255.255.255.0.
guest1, host1,
guest2 or host2
are numeric IPv6 addresses, they can be between braces,
e.g. [2001:db8:3003:1::543:210f].
If these arguments are specified, they must precede the required arguments.
-t size or --mtu size
where size is the maximum transmission
unit size. The default size is 1500.
-x name or --if name
Specifies the name of the TUN interface to use.
There is no default for name.
If these arguments are specified, they must precede the required arguments.
-m MAC address or --mac MAC address
where 'MAC address' is the optional hardware address for
the virtual interface in the format: hh:hh:hh:hh:hh:hh. The default value
is '00:00:5E:nn:nn:nn' where the :nn:nn:nn portion is constructed
from the last 3 octets of the specified guestip.
Note: The MAC address you specify for this option must be unique
as seen by all other devices on your network. It should never,
for example, be the same as the host adapter MAC address specified
on the -n parameter.
-k kernel-capture-buffer-size
-i tuntap32-i/o-buffer-size
Refer to the Help file included with Fish's CTCI-WIN product for further details and information.
If these arguments are specified, they must precede the required arguments:
-n name or --dev name
Specifies the name of the tunnel device to use.
The default
for Linux is /dev/net/tun
(which is correct for version 2.4
and above of the Linux kernel).
The default for OSX is /dev/tun0.
For Windows, specify the IP address or MAC address of the real Windows adapter to emulate the virtual guest's adapter on. The default is the first adapter found according to Windows' adapter binding order, which may not be the one you want if you have multiple adapters.
Refer to the Help file included with Fish's CTCI-WIN product for for more information about adapter binding order and for general information regarding CTCI-WIN configuration.
-4 or --inet
Indicates that when a host name is specified for
guest1, the host name must
resolve to an IPv4 address.
-6 or --inet6
Indicates that when a host name is specified for
guest1, the host name must
resolve to an IPv6 address.
-d or --debug
Specifies that debugging output is to be produced on the Hercules control panel. This should normally be left unspecified.
emulates an OSA Express card running in QDIO mode. Both layer-2 and layer-3 are currently supported.
ifname interface
Specifies the interface name of a host interface
that is already configured (e.g. tun,
tun0, etc). (*nix only)
iface device
Specifies the name of the host tunnel device to use.
The default for Linux is
/dev/net/tun
(which is correct for version 2.4 and above of the Linux kernel).
The default for OSX is
/dev/tun0.
For Windows, specify the IP address or MAC address of your Windows host's real network adapter that the Hercules driver should use to emulate your virtual guest's adapter on. The default is the first adapter found according to Windows' adapter binding order, which may not be the one you want if you have multiple adapters.
Refer to the Help file included with Fish's CTCI-WIN product for for more information about adapter binding order and for general information regarding CTCI-WIN configuration.
ipaddr address
ipaddr address/prefix
Specifies the IPv4 address to be assigned to your virtual OSA Express card.
The address can be optionally followed by a prefix size
expressed in CIDR notation, e.g. 192.168.1.1/24.
For IPv4 the prefix size can have a value from 0 to 32.
If not specified a value of 32 is assumed.
The prefix size is used to produce an equivalent subnet mask.
For example, a value of 24 produces a subnet mask of 255.255.255.0.
netmask mask
Specifies the subnet mask to be used with your OSA card.
The netmask option may only be specified when
the subnet mask is not already defined via the optional
prefix size parameter of the ipaddr option.
ipaddr6 address
ipaddr6 address/prefix
Specifies the IPv6 address to be assigned to your OSA card.
The address can be optionally followed by the prefix size
expressed in CIDR notation, e.g.
2001:db8:3003:1::543:210f/48.
For IPv6 the prefix size can have a value from 0 to 128. If
not specified a value of 128 is assumed. The prefix size
is used to produce an equivalent subnet mask.
hwaddr MAC
Specifies the MAC address to be assigned to your OSA card. If not specified then one will be internally generated in the range 02:00:5E:80:00:00 - 02:00:5E:FF:FF:FF using the low order 23 bits of the IPv4 address. For example, if the ipv4 address is 10.1.2.3 the generated MAC address will be 02:00:5E:81:02:03.
Note: The MAC address you specify for this option must be unique
as seen by all other devices on your network. It should never,
for example, be the same as the real host adapter's MAC address
as identified by the iface parameter.
mtu bytes
Specifies the Maximum Transmission Unit to be used. The maximum transmission unit (MTU) is the largest packet size, measured in bytes, that can be transmitted over a network.
chpid id
Specifies the channel path identifier to be used with the device. This is mostly a cosmetic value but certain guest operating systems such as z/OS might require it to operate correctly.
debug
Enables debug logging for the device. When logging is enabled the Hercules driver logs extra progress and status messages used to help debug an incorrectly functioning driver.
The argument specifies the name of a file containing the disk CKD DASD image or the INET address of a Hercules shared device server.
The file consists of a 512-byte device header record followed by fixed length track images. The length of each track image depends on the emulated device type, and is always rounded up to the next multiple of 512 bytes.
Volumes larger than 2GB (for example, the 3390 model 3) can be supported by spreading the data across more than one file. Each file contains a whole number of cylinders. The first file (which contains cylinders 0-2518 in the case of a 3390) usually has _1 as the last two characters of its name. The ckddasd driver allocates the remaining files by replacing the last character of the file name by the characters 2, 3, etc.
Note: When CKD DASD images are spread across multiple files, you must specify only the first file name (the file with suffix _1) in the configuration statement.
If your operating system supports large file sizes (or 64-bit offsets) then volumes larger than 2G can be kept in a single file.
Alternatively, the argument may specify the name of a file containing a compressed CKD DASD image. The CKD driver will automatically detect whether the file contains a regular CKD image or a compressed CKD image.
Refer to "Creating an empty DASD volume" in the "Creating, formatting, and loading DASD volumes" section of the Creating DASD web page for information on using the 'dasdinit' command/utility to create compressed dasd files. Refer to the Compressed Dasd Emulation page for details on the actual CCKD emulation itself and additional information on the CCKD initialization/tuning control file statement.
If you specify an INET address, the format is:
ip-name-or-addr:port:devnum
ip-name-or-addr specifies the internet name or address where the Hercules shared device server is running.
port specifies the port number the shared device server is listening on. If omitted, the default is 3990.
devnum specifies the device number on the shared device server. If omitted, the default is the current device number.
In addition to the above, some additional optional arguments are also supported.
sf=shadow-file-name
A shadow file contains all the changes made to the emulated dasd since it was created, until the next shadow file is created. The moment of the shadow file's creation can be thought of as a snapshot of the current emulated dasd at that time, because if the shadow file is later removed, then the emulated dasd reverts back to the state it was at when the snapshot was taken.
Using shadow files, you can keep the base file on a read-only device such as cdrom, or change the base file attributes to read-only, ensuring that this file can never be corrupted.
Hercules console commands are provided to add a new shadow file, remove the current shadow file (with or without backward merge), compress the current shadow file, and display the shadow file status and statistics
For detailed information regarding shadow files and their use, please see the "Shadow Files" section of the Compressed Dasd Emulation web page.
[no]syncio
Syncio enables possible 'synchronous' i/o. This is a dasd i/o feature wherein guest i/o requests are completed "synchronously" during the actual emulated execution of the SIO/SSCH (start-i/o / start subchannel) instruction rather than being deferred and executed asynchronously in a separate device i/o thread.
Only i/o which are known to be able to be completed without actually needing to perform any actual host i/o are completed synchronously (e.g. whenever the data being requested is found to already be in cache). If the requested data is not found in the cache, then an actual host i/o will need to be done and the request is passed to a device i/o thread to be completed asyncronously instead.
syncio is the default for ckd. syncio statistics may be displayed via
the Hercules syncio panel command.
syncio may be abbreviated as
syio
readonly
Readonly returns "write inhibited" sense when a write is attempted. Note that not all of the sense bits may be getting set absolutely correctly however. (Some people have reported getting different error messages under Hercules than a real machine, but it really hasn't been an issue for a while now.)
readonly may be abbreviated as
rdonly or ro
fakewrite
Fakewrite is a kludge for the readonly sense problem mentioned above. Here the disk is not intended to be updated (MVS updates the DSCB last referenced field for a readonly file) and any writes appear to be successful even though nothing actually gets written.
fakewrite may be abbreviated as
fakewrt or fw
[no]lazywrite
[no]fulltrackio
These options have been deprecated. They are still accepted, but they do absolutely nothing.
fulltrackio may be abbreviated as
fulltrkio or ftio
cu=type
Specifies the type of control unit to which this device is attached. The use of this parameter does not necessarily imply that all functions of the specified control unit are emulated, its only purpose is to force a particular control unit type to be indicated in the data returned by SENSE ID and similar CCW's.
The default value depends on the device type:
Device type Default CU type 2311 2841 2314 2314 3330 3340
3350 3375
33803880 3390 3990 9345 9343
Other values which may be specified are: 3990-3 and 3990-6.
Normally the default value is appropriate and this parameter need not be specified.
The argument specifies the name of a file which contains the FBA DASD image or the INET address of a Hercules shared device server.
The file consists of fixed length 512-byte records, each of which represents one physical block of the emulated disk.
To allow access to a minidisk within a full-pack FBA DASD image file, two additional arguments may be specified after the file name:
origin
Specifies the relative block number within the DASD image file at which the minidisk begins. The number must be less than the number of blocks in the file. The default origin is zero.
numblks
Specifies the number of 512-byte blocks in the minidisk. This number must not exceed the number of blocks in the file minus the origin. If omitted, or if specified as an asterisk, then the minidisk continues to the end of the DASD image file.
If you specify an INET address the format is:
ip-name-or-addr:port:devnum
ip-name-or-addr specifies the internet name or address where the Hercules shared device server is running.
port specifies the port number the shared device server is listening on. If omitted, the default is 3990.
devnum specifies the device number on the shared device server. If omitted, the default is the current device number.
In addition to the above, some additional optional arguments are also supported.
sf=shadow-file-name
The handling of shadow files for FBA devices is identical as that for
CKD devices. Please refer to the preceding CKD section for information
regarding use of the sf= shadow file option.
[no]syncio
Syncio enables possible 'synchronous' i/o and is explained in detail in the preceding CKD dasd section. Note however that syncio is currently disabled by default for FBA dasd due to an as yet unresolved problem and must therefore be specifically enabled if you wish to use it for FBA dasd.
syncio may be abbreviated as
syio
(Preliminary 2703 BSC Support)
Describes a BSC emulation line entry to either link 2 Hercules engines or a custom made program emulating a 2780, 3780 or 3x74, or a custom made program interfacing to a real BSC line. The line emulates a point-to-point BSC link. There is no point-to-multipoint handling.
The communication is emulated over a TCP connection. All bytes are transfered as-is (except for doubling DLE in transparent mode) just like it would over a real BSC link. Emulated EIA (DCD, DTR, CTS, etc..) or X.21/V.11 leads (C, T, etc..) are treated differently depending on the DIAL option selected.
The following options define the line emulation behaviour:
DIAL=IN | OUT | INOUT | NO
Specifies call direction (if any). If DIAL=NO is specified, the
TCP outgoing connection is attempted as soon as an 'ENABLE' CCW is executed.
Also, in this mode, an incoming connection will always be accepted. If DIAL=IN|INOUT
is specified, a TCP incoming call is accepted ONLY if an 'ENABLE' CCW is currently
executing on the device. If DIAL=OUT, the 'ENABLE' CCW is rejected.
When DIAL=IN|INOUT is specified, a DIAL CCW allows the application
to establish a TCP connection to a specific host. For other DIAL values,
the DIAL CCW is rejected.
LHOST=hostname | ip address | *
Specifies which IP address to listen on. This also conditions the network
interface from which incoming calls will be accepted. Specifying '*' means
all incoming TCP calls are accepted, regardless of the destination IP
address or call origin. This is the default value. Specifying a specific
IP address when DIAL=OUT is specified has no effect.
LPORT=service name | port number
Specifies the TCP port for which to listen to incoming TCP calls. This
value is mandatory for DIAL=IN|INOUT|NO. It is ignored for DIAL=OUT.
RHOST=hostname | ip address
RPORT=service name | port number
Specifies the remote host and port to which to direct a TCP connection on a
DIAL=NO line when an 'ENABLE' CCW is executed. This option is mandatory when DIAL=NO
is specified. It is ignored for other DIAL values.
RTO=0 | -1 | nnn | 3000
Specifies the number of milliseconds before terminating a read on a timeout, when no read termination control character is received. Specifying 0 means the READ ends immediately. -1 specifies there is no timeout.
PTO=0 | -1 | nnn | 3000
Specifies the number of milliseconds before terminating a POLL on a timeout, when no ACK or NACK sequence is received. Specifying 0 means the POLL ends immediately. -1 specifies there is no timeout.
ETO=0 | -1 | nnn | 10000
Specifies the number of milliseconds before terminating an ENABLE operation on a timeout.
the timeout applies when DIAL=NO|IN|INOUT is specified, the outgoing TCP call
fails (DIAL=NO) and there is no previously or currently established TCP connection
for this line. When DIAL=NO is specified, the timeout defaults to 10 seconds.
For DIAL=IN|INOUT, the timeout defaults to -1.
(Preliminary 2703 TELE2 TTY Support)
Describes a 2703 Telegraph Terminal Control Type II (TTY 33/35) stop/start line, providing access to the Host OS via a standard TELNET client. To the host OS the line emulates an asynchronous TELE2 connection. The communication is emulated over a TELNET connection.
The following options define the line emulation behaviour:
LPORT=port number
Specifies the TCPIP port to listen on for incoming TCP calls.
DIAL=IN
Specifies that this line is for in-bound calls. Required.
TERM=TTY
Specifies that this definition is for a TTY port. Required
The following are some additional options that may also be specified for 2703 devices:
APPEND=hh...
PREPEND=hh...
Specifies up to four bytes (in S/370 channel format, not ASCII) to be prepended or appended to input line data received from terminals before they are sent to the guest OS. Typical use is to add Circle D and C around each input transmission (2741's for APL\360).
BINARY=NO | YES
Negotiate to telnet binary mode if TERM=RXVT4APL.
BS=DUMB
BREAK=DUMB
Backspace and break key handling option.
When using windows telnet it is recommended to always use BS=DUMB and BREAK=DUMB.
CODE=EBCD | CORR | NONE
Specify code=ebcd for EBCD, code=corr for correspondence code, or code=none to disable all translation. The code= option applies to 2741 mode only.
CRLF=YES | NO
Option to map 2741 NL to TTY CRLF sequence.
CRLF2CR=YES | NO
Remove LF that immediately follow CR.
EOL=hh
Specifies the ASCII byte value that, when received, marks the end of the input line. The default is EOL=0D.
ISKIP=hh...
Specifies up to four ASCII bytes that are to be suppressed during input processing.
KA=NO | (idle,intv,count)
Defines the TCP/IP keepalive settings for this line's connections. Refer the the CONKPALV statement for details.
LNCTL=TELE2 | IBM1 | BSC
Specifies the type of communications line being defined.
For asynchronous communications lines specify LNCTL=TELE2 if TERM=TTY or LNCTL=IBM1 if TERM=2741. For binary synchronous (BSC) lines specify LNCTL=BSC.
SKIP=hh...
Specifies "garbage" code points (either byte-reversed ASCII for TERM=TTY or correspondence code/EBCD for TERM=2741) that are to be suppressed in output processing, thereby allowing distinct lists to be used for different terminal types.
SENDCR=NO | YES
Send CR back to terminal when input line received.
SWITCHED=IN | OUT | INOUT | NO
Switched is just a synonym for the DIAL option.
TERM=TTY | 2741 | RXVT4APL
Specifies the terminal type. Use RXVT4APL for 8-bit and character translation in 2741 mode.
UCTRANS=YES | NO
Enable automatic translation to uppercase.
If you have a question about Hercules, see the Hercules Frequently-Asked Questions page.
Last updated $Date$ $Revision$